ASME B16.34 600LB Top Entry Ball Valve

Size:	Size: NPS 2" To 48"	Pressure:	150LB To 2500LB
Temperature:	-196℃~610℃ Low Temperatue, Normal Temperature And High Temperature	Body And Trim:	Cast Steel, WCB,ASTM A105, ASTM A350 LF2, ASTM A182 F304 F304L F316/F316L/F51 F53 F55,ASTM A351 CF8 CF8M CF3M ASTM A182 F6a 17-4PH
Seat Material:	PTFE, RPTFE, DEVLON, Molon,PEEK,Metal Seat	Body And Stem Sealing:	Oring(FKM,FFKM NBR,FPM HNBR, VITON,EPDM, AFLAS), Spiral Wound Gasket(316SS+ Graphite) Packing(Graphite, PTFE)
Operation:	Wrench, Lever, Gearbox, Pneumatic, Hydraulic, Electric.	Design Feature:	Casting ,Forging, Full Bore,Reduced Bore,Integral Body,Three-pc Ball Valve,Side Entry Design,Split Body, Top Entry Design,Metal To Metal Sealing,
High Light:	nps 32 inch top entry valve ,  asme b16.3 full bore ball valve ,  600lb reduced bore ball valve

Top Entry Ball Valve 600LB

Design Feature

1: Full bore or reduced bore

2: Integral body structure

3: Double Block & Bleed, Double isolation and bleed(DIB-1&DIB-2)

4: Fire safe design(API 607)

5: Blowout-proof system

6: Anti-static design

7: Self cavity relief

8: Fugitive emission testing(optional)

The ball is fixed by trunnion and stem for size 4” &smaller. Trunnion plate support for size 6” & larger

 

Design Data

Design standard: API 6D,DIN3357-1 , EN12516-1

Face to Face standard: API6D, ASME B16.10, DIN3202

Connecting Standard: ASME B 16.5, ASME B16.47, DIN 2543/4,ASME B 16.25

Test & Inspect Standard: API 6D ,API 598

Working Temperature: -196℃~610℃

Connection type: RF,RTJ,FF,BW.BSPT,NPT

Sour environment:NACE MR0175

Design Standard		API6D
Pressure-Temperature Rating		ASME B16.34
Face to Face		API6D
Flange Ends		ASME B16.5, ASME B16. 47
Buttwelding ends		ASME B16.25
Inspection & Test		API598/ API6D
Test Pressure	Shell Test	CL150	CL300	CL600	CL900	CL1500
	High Pressure Seal Test	2.93	7.55	15	22.4	37.5
	Low Pressure Seal Test	2.07	5.52	11.03	16.54	27.5

 

Fire safe design

Coosai ball valves ensures 100% pass of the fire safe test. As Coosai Ball valve applies two sealed design via O-ring seals and metal graphite spiral wound gasket. When the valve is on fire, non-metallic materials such as PTFE seat seals, gaskets ,O-ring seals,rubber etc will be damaged, meanwhile the outer layer of metal graphite spiral wound gasket provides a secondary seal. When the soft seat is burned, metal seat will automatically form a metal seal with ball under the urging of the spring which will effectively control the internal leakage and external leakage. Valve design fully accords with API 607, API 6FA, BS 6755, JB / T 6899 and other standards,

Grease injection device

For DN150 (NPS 6) & larger the stem and the valve seat are provided with a sealing grease injection device, For DN125 & smaller, we can provide the sealing grease injection device according to customer requirements. When the O-ring is damaged by accident, by injected sealant sealed to prevent the media through the valve seat ring and stem leaks.

DOUBLE BLOCK & BLEED (DBB)

When the ball is in the closed position, each seat seals off the process medium independently at the same time between the up/down stream and body cavity, it allows bleeding the trapped cavity pressure (DBB) through drain and vent valve. The double block and bleed function make it possible to flush the valve under pressure and verify that the seat are sealing properly.

DOUBLE ISOLATION & BLEED (DIB)

Double piston effect seat, medium pressure, both upstream and downstream as well as in the body cavity, creates a resultant thrust that pushes the seat ring against the ball, valve with double piston effect seat rings require a cavity pressure relief to reduce the build-up of over pressure in the body cavity.

Blow-out proof stem:

The stem is made separately from the ball with integral T-type round shoulder, retained by bland .(other designs are Available on request)

 

Anti-static device:

Spring plus graphite type anti-static device are applied between the ball ,stem, gland Flange and body to keep the electrical Continuity between all the metallic components . And ensure the resistance lower than the most severe service requirement.

 

Sealing Options

Soft seat: Metal to Metal O-Ring seal

Simple structure reliable sealing Applicable to particulate Reliable sealing low torque meet customers' high

wide application low cost. media conditions sealing reliability and low torque requirements

SQ41 Top entry ball valve

 

Material of major parts

№	Accessory name	Material ASTM
1	Body	A216 WCB/A105
2	Seat	Rubber ring
3	Seat ring	A182-F304
4	Sealing rings	PTFE
5	Ball	Graphite+F304
6	Stem	A276 410
7	Sealing gaskel	PTFE
8	Valve bonnet	A216 WCB/A105
9	Packing	Graphite
10	Packing gland	A216 WCB
11	Stud	A193 B7
12	Lever	A216 WCB
13	Nut	A194 2H
14	Stud	A193 B7

Note: Major parts of the valve series and materials of sealing surface differs according to different working condition and customers’ special requirements.